<meta name="google-site-verification" content="e-neHNBj_m4MfBo4s3jSyGYZwmyK9GYZsgbbnUCM848" />

Professional China Aluminium Coil 3004/3104 For Can Body for Tajikistan Importers

Short Description:


Product Detail

FAQ

Product Tags

It is our responsibility to meet your needs and efficiently serve you. Your satisfaction is our best reward. We are looking forward to your visit for joint growth for Professional China Aluminium Coil 3004/3104 For Can Body for Tajikistan Importers, We welcome new and old customers from all walks of life to contact us for future business relationships and mutual success!


 

Alloy

temper

Sizes(mm)

Standard

thickness

width

ID

3004/3104 H19 H14 0.20~0.35 200~1660 200,300,350,405,505,605 GB/T3190GB/T3199GB/T228

ALUMINIUM COIL 3004/3104 FOR CAN BODY OF RING-PULL CAN

Application:widely used in body of  ring-pull can,bottle cap,color aluminum sheet,building materials,roof board,aluminum pot,radiator,cosmetic packing,materials for ships etc.

 

JIDING ALUMINIUM INDUSATRY CO.,LTD

Professional manufacturer of kinds of high-quality aluminium sheet/coil/foil.

  • Previous:
  • Next:
  • FAQ Content




  • An animation illustrating a complete cycle of aluminium extrusion production, including: die heating and transfer, billet heating, sawing, transfer to press, extrusion, cooling, sawing, stretching, stacking and ageing.

    Before extrusion begins, the die is also heated in a furnace. The die is a steel disk containing one or more cavities through which the aluminium is extruded. The die assembly is lowered into a holder and transferred into position within the press.

    The aluminium billets are heated in order to make them soft and then sawn to the required length. Before entering the press, the rear face is sprayed with a release agent to prevent it from sticking to the ram.

    Note that the billets are often heated so that the front end is hotter than the rear (taper heating). This is because as the billet progressively deforms in the press, it also heats up due to friction and deformation.

    Once inside the press, the billet is initially compressed and expands outwards to fill the container. Any trapped air is released by withdrawing the container/billet from the die face.

    The main extrusion cycle begins and as the profile emerges, it is cooled using air or water sprays in order to develop its metallurgical properties. At the end of extrusion, there is still a small length of billet remaining. This ‘butt end’ is sheared off in order to present a flat face for the subsequent billet to join onto.

    The extrusion is sawn off just past the cooling zone and then transferred to the stretcher. A small stretch is applied in order to remove any distortions and straighten the profile. This is then sawn to the final length.

    Finally, the profiles are stacked and may then go on for further processing, such as painting, anodizing or ageing, in order to produce the required surface finish, mechanical properties and corrosion resistance.

    This animation was developed and released by Sapa AB and Materials e-Learning Technologies under a Creative Commons Attribution-ShareAlike 3.0 unported iicense.



    Shannon from https://www.house-improvements.com/forums/ shows you how to replace a ceiling light fixture. **If you have any doubts as to your ability, are not comfortable doing this, or are not allowed to do this as per electrical code in your area, be sure to hire a licensed electrician to perform this work** If you have any questions about your home DIY projects, stop by the forum on our website and ask. Video © 2014 SKS Media.

    Videos produced by SKS Media (House-Improvements.com) are provided for informational purposes only. The information contained in the videos is intended to give general guidance to simplify DIY (do it yourself) projects. Because tools, products, materials, equipment, techniques, building codes and local regulations are constantly changing, SKS Media cannot and does not assume any responsibility or liability for the accuracy of the information contained therein. Further, SKS Media will not accept any claim for liability related to, but not limited to, omissions, errors, injury, damage or the outcome of any project. It is the responsibility of the viewer to ensure compliance with all applicable laws, rules, codes and regulations for a project. The viewer must always take proper safety precautions and exercise caution when taking on any project. If there are any questions or doubt in regards to the element of a project, please consult with a licensed professional. SKS Media conducts all matters in accordance with the laws of Saskatchewan, Canada.

    Send your message to us:

    Write your message here and send it to us

    Related Products

    Send your message to us:

    Write your message here and send it to us