16 Years manufacturer Medicine Aluminum Foil to Morocco Importers

Short Description:


Product Detail

FAQ

Product Tags

We support our buyers with ideal high quality products and high level service. Becoming the specialist manufacturer in this sector, we have gained rich practical experience in producing and managing for 16 Years manufacturer Medicine Aluminum Foil to Morocco Importers, Any requires from you will be paid with our best attention!


Technical Specifications
♦ Thickness: 0.02-0.3mm
♦ Width: 250-1280mm
♦ Material (alloy): 8011, 8021
♦ Temper:H18,O

Specifications pharmaceutical aluminum foil for medicine
pharmaceutical aluminum foil for medicine also called Pharmaceutical Aluminum Foil,blister Aluminium Foil
Inner hole diameter 76mm, length/roll:1000m (according to different requirement).one side is for sealing with pvc or pvc/pvdc film and other side is for printing.one side is bright and other side is dull.Inner hole diameter 76mm, length/roll:1000m (according to different requirement).

Functions:
High obstruction, Heat insulation, Air tightness, Printable, Breakable in slightly.

Medicine Aluminum Foil Applications:
It can be applied to blister packing for torches, pills, suppositories and mini-foods/candies, chocolate, chutty and so on.

Blister Foil(cold forming)
♦ To be laminated, used for alu alu foil.
♦ Alloy: 8021
♦ Temper:O
♦ Gauge:0.045mm-0.075mm
♦ Width:200mm-1100mm
♦ Surface Finishing: one side bright, one side matte.

Blister Foil(PTP Packaging)
♦ To be lacquered, used for PTP packaging
♦ Alloy:8011
♦ Temper:H18
♦ Gauge:0.02mm-0.03mm
♦ Width:200mm-1100mm
♦ Surface Finishing: one side bright, one side matte.

Pharmaceutical aluminium foil (blister foil)
One side is coated HSL for heat sealing with PVC/PVDC for packing tablets,capsules,etc.The other side is printed or coated primer for printing.

  • Previous:
  • Next:
  • FAQ Content




  • From https://www.kevincaron.com – Artist Kevin Caron shows how to seamlessly weld together two pieces of metal pipe, rod or square tubing ….

    Sometimes you are working on a project – making a fence, a cage, whatever – and your pipe or rod is a little short, so you want to add a piece of scrap to get your correct length and have a smooth piece of pipe. To show you how to join them to make a single piece of metal pipe or rod, Caron starts by taking two lengths of metal pipe over to his chopsaw. But before he puts his stock into the saw, he uses his framing square to check against the backstop and the blade to make sure the chopsaw is set at 90 degrees before he makes his cut. Once that’s confirmed, he secures the stock. Caron emphasizes, though, that when you put your stock into the chopsaw, you don’t have to crush it – just make sure it’s snug. He puts on his safety glasses and hearing protection, then cuts off the ends of both of the pieces he is going to join to get a clean, straight area. Next he goes over to his bench grinder, which he’s modified so he can add a 4-1/2″ soft pad – which he usually uses on his hand-held angle grinder – on the outside of the grinding wheel. He dresses the edge of each pipe, giving it a nice chamfer, or bevel, and touches the flat end of the pipe to remove any burrs so it will jig up neatly. He lays both pieces of pipe on a piece of thick-walled angle iron, which gives him a straight 90-degree edge – the angle iron is great for square tubing and pipe. Everything fits together and lines up so he can weld down into the joint. He has a good kerf that gives ample penetration while allowing him to grind the welded joint smooth and flush. Next he clamps down each pipe with a Kantwist clamp, which has an X in its bottom pad that lets you lock everything in place. Because it’s a tiny joint, Caron uses 1/16″ E3 tungsten sharpened almost to a point and some 1/16″ filler rod in his TIG welder. Caron then tacks both sides of the pipe because a single tack on the top can result in a bow. Then he welds a small tack on the top, rolls the pipe over, reclamps it, and gets a tack on the other side. So now he has tacked it on all four “corners.” Then he welds between the tacks. When the welding is done, he lets the pipe cool down a minute or two, then uses his 4-1/2″ angle grinder with a soft pad to smooth the surface. Caron checks his work with a straight edge, looking for light between the pipe and the straight edge. Finally, he can finish the job with some 80 grit and some 120 grit with long passes to hide the weld. For more how-to videos, visit https://www.kevincaron.com



    All in one Roof furniture Manufacturing Unit, Having
    Automated Pipe Cutting Machine,
    Automated Pipe Bending Machine,
    7 Tank Powder Coating Unit,
    Steel Pipe Buffing Machine,
    Metal & Steel Heavy Sheet Bending Machine,
    Glass Cutting Machine,
    Glass Polish Machine

    We have large Furniture Manufacturing Unit all in one Roof
    of all kinds of Steel, Metal, Wooden, Outdoor Wicker Furniture

    Related Products