Special Design for 1050 Aluminum Sheet to Sheffield Manufacturer

Short Description:


Product Detail

FAQ

Product Tags

It adheres to the tenet "Honest, industrious, enterprising, innovative" to develop new products constantly. It regards customers, success as its own success. Let us develop prosperous future hand in hand for Special Design for 1050 Aluminum Sheet to Sheffield Manufacturer, We warmly welcome all interested customers to contact us for more information.


1050 Aluminum Sheet 

Specifications

♦ alloy:1050
♦ temper:O~H112
♦ width:500mm-1500mm
♦ SGS & ISO
♦ Length:according to your requirements

1000 Aluminum Sheet Features
♦ This series aluminum sheet, also called pure aluminum sheet, has the highest aluminum content among all the series produced by Mintai. Its aluminum content can be more than 99.00%.
1000 Series: 1050 1060 1070 1100 1200 1235 etc.

♦ As no other techniques are involved in the production, the production procedure is single and the price is cheap. It is a commonly used aluminum sheet in conventional industries.

♦ The last two numbers in the serial number are used to determine the lowest aluminum content of this series. For example, in the 1050 series, the last two numbers are 50 and according to the corresponding international standard, the aluminum content has to reach 99.5% or more. In GB/T3880-2006, the technical standard of aluminum alloy in China, 1050 series also means the aluminum content has to reach 99.5%. Similarly, the aluminum content of 1060 series aluminum sheet has to reach 99.6% or more.

1000 Aluminun sheet

This series aluminum sheet provided includes 1100, 1050, 1070 series, etc. The 1050, 1060 and 1070 series are representative series.

Type Alloy Temper Thickness Width Application
sheet 1050 O, H12, H14, H16, H18 0.3-0.5mm
0.5-1.0mm
1.0-5.0mm
400-700mm 
700-1600mm 
>1600mm
Conducors,hoses,,marine accessories.
1060 Chemical and marine equipment
1070 Capacitor ventliation system compents
1100 Reflective devices,pipe,storage,Etc.
Other Products Aluminum plate 3xxx,5xxx,6xxx, Diverse temper
Aluminum tape 1xxx,3xxx,5xxx,6xxx,
Aluminum coils 1xxx,3xxx,5xxx,6xxx,
Aluminum foil 8011 O

1100 Aluminum Sheet Low strength aluminum alloy has excellent corrosion resistance and satisfactory anodizing and conversion coating finishing characteristics. It is unmatched by any other commercial aluminum alloy in workability. Readily to welding, brazing, and soldering. Machinability is poor and tends to be “gummy”. Non-heat treatable. 

As a China-based 1050 aluminum sheet manufacturer and supplier, we  also produce coated aluminum coil, aluminum plate, aluminium slit coil, aluminum strip, anodising aluminum sheet, embossed aluminum sheet, etc. For more detailed information, please continue browsing our website or feel free to contact us directly.

  • Previous:
  • Next:
  • FAQ Content




  • Special deal today, click the link : http://po.st/ZwY1kS

    Two types of flex transition hose to connect the dryer to the wall outlet. This video discusses the pros and cons of each and demonstrates tricks or tips to best secure the flex hose. Safe Dryer Venting. Protect your home from a dryer fire. Make your laundry room feel bigger.

    New for 2012 is this pretty impressive DryerFlex product. See it at www.dryerflex.com

    My lengthy reply to the comment from mid 2012.

    The connection between the dryer and the wall outlet in the majority of cases, if not 90% of them, requires some sort of expandable and flexible hose, so that a person can make the positive connection to each outlet. In cases where the dryer can be located far enough away from the wall to allow access to make those two positive connections with hard pipe, then I agree, rigid or hard pipe is the best.

    A point you hinted around was that screws and tape should be used at each joint or connection. Both the International Building Code and the Uniform Building Code explicitly point out that any sort of penetration (screw) is forbidden. The most popular and dependable mechanism to tighten the flex hose around the rigid pipe is the worm drive hose clamp.

    The wire bound foil flex is very easy to work with and has impressive stretch to compressed ratio but since the foil material collapses or folds within the opening, the 4 inch space shrinks to a very abrasive 3 ¼” opening, increasing the airflow friction and therefore a poor choice when considering efficiency.

    The aluminum flex or semi rigid flex, which is often specified in the dryer manufacturers’ installation manual due to its fire retardant capabilities is much more difficult to work with, exhibits very poor stretch to compression ratio and just meets the testing standards set forth in the International Building Code dealing with its puncture and deforming characteristics. The value in using this flex is that the inside dimension of 4″ is never compromised and the smooth interior surfaces provide little friction and therefore a smart efficiency choice.

    What I have discovered is a brand new and very impressive hybrid flex that combines the ease of use and flexibility of the wire-bound foil flex with the fire resistance and airflow efficiency of semi-rigid aluminum flex. And this is the only flexible duct on the market that has a zero flame spread and zero smoke development rating and that meets the International Residential & Mechanical Codes M1502 and 504 to be specific which require meeting the UL2158A standard.

    Let’s revisit the deformation and puncture issues that the code references. When I applied equal pressure to the three types of flex, I noted how well the DryerFlex recovered from the effort to deform it. The aluminum flex easily deformed and did not rebound.

    For whatever it is worth, there are hundreds of national and independent duct cleaning firms that have switched 100% to the DryerFlex product. Yeah, hard to believe, but once you hold this new Dryer-Flex in your own hand you’ll see why. In my honest opinion it is the safest, most efficient and easiest to work with clothes dryer transition duct on the market. I did my own fire test, and it is installed in my house. Thanks again for the comment.



    how to lit leds with an aluminum paper…

    Comment allumer des leds avec un papier d’aluminium…
    La haute tension engendre des champs électriques utilisables à distance.C’est le principe des émetteurs.Reste à savoir si ce type de montage est surunitaire (???). Certains de mes essais ont l’air de le confirmer mais d’autres non…

    Et si vous voulez me soutenir dans mes expériences, vous pouvez le faire sur le site de financement participatif Tipeee :

    https://www.tipeee.com/stellaebe

    Merci d’avance même si ce n’est qu’un euro !

    Related Products