19 Years Factory Brushed aluminum sheet/Coil to Cancun Manufacturer

Short Description:


Product Detail

FAQ

Product Tags

With a sound business credit, excellent after-sales service and modern manufacturing facilities, we have earned an excellent reputation among our customers across the world for 19 Years Factory Brushed aluminum sheet/Coil to Cancun Manufacturer, We warmly welcome you to establish cooperation and create a bright future together with us


Products Details

 Item  brushed aluminium sheet ,brush aluminum coil
Standard  ASTM AISI, SUS, EN, JIS, DIN, GB ASME
 Other Material  1060, 1050, 1070, 1100, 3003, 3004, 5052,
5652, 5154, 5254, 5454, 5083, 5086, 5056,
5456, 2024, 2014, 6061, 6063. etc
Thickness  0.1mm-200mm 
Width  500mm,1000mm,220mm, 250mm,1500mm,or be required
Length  1000mm,2000mm,2440mm,3000mm,3048mm,6000mm, or as required 
  

 

 

 

 

 

 

 

 

 

   Application 

1. Lighting 2, solar reflector plate 

3, architectural appearance 

4, interior decoration: ceiling, metope, furniture, cabinets and so on 

5,elevator 

6, plate, nameplate, bags 

7, automotive interior and exterior decoration  8. Interior decoration: such as photo frame 

9, household appliances, refrigerator, microwave oven, audio 

equipment, etc. 

10. Aerospace and military aspects, such as China’s 

current large aircraft, the shenzhou spacecraft series, satellite, etc. 

11, machinery parts processing, mold manufacturing 

12, chemical/insulation pipeline coating

  • Previous:
  • Next:
  • FAQ Content




  • Website:http://www.firstprinters.com
    The New printer except UV printer’s function, It add vacuum table.
    ECO Solvent Printing on Aluminium Sheet use the vacuum table easy to put aluminium sheet.



    http://ddmgaragedoors.com/

    To buy PVC stop molding go to http://ddmgaragedoors.com/parts/garage_door_seals_top_side_seals.html

    Clarification at 2:33 where we show a right angle and say, “If the seal is properly aligned the flap will create a 45 degree angle.” The stop and door meet at 90 degrees; the angle inside the bottom of the seal where it meets the door is 45 degrees.

    To purchase other garage door seals go to

    http://ddmgaragedoors.com/parts/garage_door_seals.html

    In this video we’ll show you how to install your garage door stop molding weather seals.

    You’ll need:
    Stop molding (3 boards)
    Hammer
    Nails
    Utility Shears/Hack Saw/Circular Saw
    Pencil/Marker
    Ruler

    Transcript:
    Hi I’m Dan Musick in this video we’ll show you how to install PVC stop molding
    to seal the sides and top your garage door.

    The flaps for vinyl stops are mounted either on the sides or the tops.
    We prefer stops with the top flap because this design allows the door to ride against the hard PVC rather than the soft flap. The only disadvantage to the top flap design
    is that the vertical and horizontal stops can’t be joined without an offset.

    To fix this problem cut the top corners of the vertical stops. This will eliminate the gap between the stops. Start by measuring the gaps on either side of the door at the top and bottom as well as each joint. To do this push in on the door and measure the gap
    you may need to adjust either the garage door opener for the top fixtures to get a consistent gap. The order in which you install stop molding is important. You need to install the overhead board first then the boards on either side so that they intersect with the top board. The reason for this is that when the door closes the flap of the top board is pushed down smoothly and the flaps on either side are moved out of the way preventing them from being torn.

    Prep the top board first by driving the nails part way into the board. You do not want them to go through just to be held in place. Place the nails six inches apart on the top board. An important warning did not hammer the nails while the board is bent. This can easily cause the board to crack and break. Lineup the board with the end of the Board flush against the door frame drive the nails into the door frame enough to hold the
    board up but not all the way through you will need to pry them out again at a later stage.

    Repeat this on every other nail up to the midpoint of the door then take the other end of the board mark the excess with a pencil and use a straight edge to extend the mark then cut the board with the implement your choice. We use utility shares but you could also use a hacksaw circular saw or anything else that creates a straight clean edge.

    Once you’ve made the cut hold up the board to check your cut and mark and re-cut is necessary. Now that the board is the proper length you’re ready to adjust the position of the board. Since it was initially putting on an angle you may need to pull out some other nails straighten the board then continue driving in every other nail from where you left off.

    Close the door to check the seal. If the seal is properly aligned the flap will create a 45 degree angle to adjust an area pull out the nearby nails move the board into position
    and hammer the nails back in. Next determine the length the side boards. First open the door then hold up the board and mark a line across with a ruler then cut in the same manner as before.

    Once you’ve made your cut check the new length. If the board is too long it will create a bubble. In this case simply re-cut the board and if needed trim the board with a razor blade. Position the board and hammer in the nails 6 to 12 inches apart and partially as before you’ll need to adjust them to fix the gap repeat the process on the opposite side then close the door.

    Once the door is down check the seal by pushing on the door if there is a gap
    you’ll need to readjust the seal to remove the gap. The reason you push on the door is that when the wind blows it forces the door back and allows the wind in which is especially bad in winter. Before finally hammering in the nails open the door this will prevent you from hitting and damaging the door while driving in the nails.

    I’m Dan Musick thank you for watching.

    Visit our most popular garage door springs page with videos at – http://ddmgaragedoors.com/diy-instructions/replace-garage-door-torsion-springs.php.
    Tutorials – http://ddmgaragedoors.com/diy-instructions/
    Garage Door Parts – http://ddmgaragedoors.com/parts/
    Garage Door Springs – http://ddmgaragedoors.com/springs/garage-door-springs.php
    Dock Leveler Parts – http://ddmgaragedoors.com/dock-leveler-parts/

    Related Products